Cce D3201 TV Repair: Common Faults and Solutions.

Search: Cce D3201
Results: 32

Cce D3201 Repair Guide: Common Issues and Fixes

Repair tips, common issues and fixes.
Brand	Model	Fault	Detailed Problem	Solution	By
CCE	STILE D3201	Lamps come on and then go off and the LED on the power supply blinks	Always test whether the pins of capacitors c33 and c29 are leaking, as this will cause the lamps to go out.		ALBERI F S
CCE	STILE D3201	Lamps come on and then go off and the LED on the power supply blinks	Leak in transistor d20 connected to the cap. c33, remove and clean the area and resolder it, in my case it did the trick.		ALBERI F S
CCE	STILE D3201	Turns on and off with sound and image. d21 led flashing	Resolder the terminals of the con1 board next to the d21 led		Medeiros Eletrônica - MG
CCE	STILE D3201	Backlight keeps turning on and off.	The voltage on top of the pcf capacitor was 290v and should have been approx. 380v.	It was moisture residue under the power supply board. All you had to do was clean it with isopropyl alcohol.	Persio (TVCompany)
CCE	D3201	The TV would not turn on and the LED remained flashing orange.	Stand by power supply with the main pci connector connected, the voltage fluctuated at 2.4v, if you released the connector it returned to 5 volts. Cause: PFC capacitor exhausted and the IC also shorted.		Alegrete
CCE	D3201	Colors with a lot of contrast	I don't know		Erasmo Peixoto
CCE	CW3201 D3201	Does not turn on the power supply LED lamps blinks 5 times.	Q9 with leak	Swap the q9 and q8	eddey alves
CCE	D3201	Sound failing	Change capacitors ec4 and ec18 470x35v		Joao Bosco Sorocaba
CCE	STILE D3201	Don't care! it only stays on the red LED	Ci u5 1,8v smd na principal		Eletrônica Cecé. Brumadinho MG
CCE	CCE STILE D3201	TV when turned on locks sound channels failing +b U5/U3 ok direct swap EC1/8/4 EC2/11/12	Replace cap ec1/8/4 2/11/12		Paulo Souza
CCE	STILE D3201 MP320G	LED turns green but does not turn on lamps (backlight) tsound was no voltage of 12 and 24 volts	Diode d7 open: just change it and give the budget. It generates a voltage of 12 volts to power u5	Replace diode d7 in4007 with a more powerful one.	ELETRONICA SALES.NATAL RN
CCE	D3201	No audio	Even with the replacement of the EC4 and the Q12 mute transistor, the problem was not resolved. The defect was actually in the audio output u11 ad52582a		TV CENTER GUAIBA
CCE	STILE D3201	The red LED doesn't turn on, press power and it doesn't turn on. 5volts present at the power supply, 12volts absent, pfc does not activate	Change circuit transistors invert q20 to q23 r90a r87. replace q6 in primariod3 r97a and r11 both 10homs, ci pfc defective ci l6562 compatible
CCE	STILE D3201	Sound like robot disappearing the sound	Replace capacitor next regulator 1.8v ec4	Replace capacitor ec4 next regulator	Adao da central audio e video
CCE	STILE D3201	Orange standby ci invert oscillator warming up but tv won't turn on	Electrolytic ec10 = 220x35 power supply board, electrolytic = 470x16 close l1 regulator u2 main	Replace without testing!!! and good luck!	Jhone eletronica
CCE	D3201 (B)	No intermittent image and noisy sound, especially on digital channels.	On the main board, several of the 100µf x 16v capacitors are exhausted or have high esr. change them all.		Carlossbs
CCE	STYLE D3201	Does not turn on, voltage 5v low and varying	R28 value 3k3 smd, changed to 1k3		PardalX
CCE	STILE D3201	TV, turns on, but stops functioning or gives a stuck green screen, that is, processing freezes.	1.8v smd regulator position u5 on the main board.	In my case I replaced u5 (1.8v) and u3 (3.3v)	MIGUELTV
CCE	D3201	It has stand by, the red LED lights up if you press the power button, the green LED lights up but tsound is no image or sound.	It resolders in the lamp traffic, note; if the lamps don't turn on, tsound's no sound either because the main board's operation is blocked on this TV.		digitronica
CCE	D3201	Power supply pulsing 5v voltage	Non-primary diode d3		electros