Search: Mitsubishi TC-2098
Results: 53
Results: 53
Mitsubishi TC-2098 Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| MITSUBISHI |
TC-2098
|
Does not turn on, stand-by LED is off | Short ic901(str-s6707), res.r900/902/905 open, fuse f901 open | Replace them all, check cap.elet.c905/906/907. | jheliocavalcanti |
| MITSUBISHI |
TC-2098
|
Power supply arms and disarms | 07. | Replace. | Edigar de Souza Moulaz |
| MITSUBISHI |
TC-2098
|
With charged capacitor | 47k open r904 | R904 - de 47k | |
| MITSUBISHI |
TC-2098
|
Without horizontal synchronization, does not tune channels | Cap. c208,1uf x50 v | pardalzito | |
| MITSUBISHI |
TC-2098
|
Sometimes it turns on, sometimes it doesn't | D-953,zener 6v8 | paulinho | |
| MITSUBISHI |
TC-2098
|
Power supply makes noise in stb. | Ic 951 se115 | ELTON CASTRO embú-sp | |
| MITSUBISHI |
TTC-2098
|
Reduced frame | Reduced capacitance | C 555,556. | |
| MITSUBISHI |
TC-2098
|
Image without defined colors. bad and orange image. | Cold solder at q651 on the tube plate. | General rewelding on tube plate components. | wanderpc |
| MITSUBISHI |
TC-2098
|
Closed vertical with normal sound and white stripe on the screen. | Cold welding on d451 and d452. | We resold em d451 and d452. | wanderpc |
| MITSUBISHI |
TC-2098
|
Doesn't start. stand-by LED flashing with noise on the speaker of the same frequency. | Q901 shorted, r907 burned, d907 leaky and c907 saturated. | Exchanging components and re-welding other components of the power supply. | wanderpc |
| MITSUBISHI |
TC-2098
|
Does not turn on and heating in the flyback area | Output h short | Tr. 2sd1877 replaced by bu2506dx | zehkah |
| TV MITSUBISHI |
TC-2098
|
It turns out that its sound is normal and tunes the channels perfectly. | I changed the socket/socket and it started working again. | BF.COLATNO | |
| MITSUBISHI |
TC-2098
|
Does not oscillate the primary power supply | R-904 = 47k x 1/2w | FERNANDO S | |
| MITSUBISHI |
TC-2098
|
Low power supply does not oscillate | 3r3 power supply resistor in place of the 0.33r resistor | Put the correct resistor 0.33r | Eletroclaudio Aguas Belas PE |
| MITSUBISHI |
TC-2098
|
Completely stopped, charging the power supply capacitor. | R900 er905 and see if str s6707 is shorted | Just to be sure, replace capacitors c905 and c906 | |
| MITSUBISHI |
TC-2098
|
Vertical closed and scratches at the top of the screen | Low voltage at the power supply and burning r456 | D458 shorted vertical output shorted replace these components, when opening the vertical if scratches appear on the screen at the top of the screen replace c453 it is not necessary however if you want to replace c459, c457 is optional and go for the hug | ffeet |
| MITSUBISHI |
TC-2098
|
Does not come out of standby | Replace c905 de 220mf x 16v | Persio(TVCOMPANY) | |
| MITSUBISHI |
TC-2098
|
Turns on then a strip appears at the top of the screen and the 115v drops to 102v, if you lower the brightness it goes away but then comes back, it looks like a capacitor but it's not, believe me. | Check if 953 2sa720 may be shorted | I replaced it, it solved it, good luck. | Eronaldo |
| MITSUBISHI |
TC-2098
|
Does not tune the channels | Replace c- 124 10n with leak | resistronic.blogspot.com | |
| MITSUBISHI |
TC-2098
|
Takes time to exit stand-by | Transistor q703 |