Search: Philips
Results: 14154
Results: 14154
Philips Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
32PFL5403 32PFL3403
|
Turns on and off with keyboard locked and in av | It has to be turned on via the control because if you try to turn it on via the keyboard it will come back on and turn off | mario moreci | |
| PHILIPS |
42PFL4007/78
|
No sound comes out | U701 altered 3.3v regulator | Replace u701 if the sound works and stops, replace the ci u603 | eletronica dvn |
| PHILIPS |
32PHG4900
|
All power supplys pulsing(oscillating) voltage | Check diodes...d9112 | ....►I went to the crowd lol ◄....º¿º | Alextecnico |
| PHILIPS |
32PFL4007D/78
|
Blue fabric | Short on tcon, several caps. measuring short and responsible for everything was the c95, hope to help someone. | Changing the cap. c95 | Arimateia |
| PHILIPS |
DVP3005/BK
|
It only had the STB LED on, it wouldn't turn on at all | 1y faulty oscillator crystal was replaced and the device worked perfectly again | ||
| PHILIPS |
49PFG5001/78
|
Turns on normally in seconds turns off | Defect in memory removed and rewritten resolved | Luis Aquino sparapan | |
| PHILIPS |
68PUG6513/78
|
TV doesn't work, nor does standby light up. | Check the power supply if it has 10v, etc... check on the main board if tsound is 5v on the ci u708 (voltage +5v_stb on the board). | Ci smd sy8366q - u708 defective | Eletrônica JM/Júlio |
| PHILIPS |
42PFL4908G/78
|
After turning it on, the becklight turned off, only sound came out | Ci (pf7900s)smd in position ic8103 cutting voltage on pin 1 | Replace the ci and go for the hug | LS ELETRÔNICA |
| PHILIPS |
40PFL3606D/78
|
Red light on, press power but it won't turn on | Blue ceramic capacitor c502 | Replace the capacitor c502, it's very bad on this TV | Wilker |
| PHILIPS |
40PFL3606
|
Back light comes on, gray screen and some lines. | After checking the 750k, 240k and 10k resistors, without success adding a 150k resistor from the r750k to the capacitor next to it, terminal nodes on the IC side (inside the board). | ||
| PHILIPS |
32PHG6825/78
|
Doesn't start | Diode d9105 | Replace the same | Pop Tron Mafra S.C. |
| PHILIPS |
20PT4331
|
Then turning off | Add 3 diodes to the tube plate to bypass the tube in the ik circuit | Put diode and solved | orlando lott |
| PHILIPS |
FWM6000
|
Lowering the volume alone | Fan doesn't fire | In my case, it was the damaged fan drive transistor | Stiltec |
| PHILIPS |
32/42PFL3007D/78
|
Hdmi doesn't work | Regulator u701 with 4.2 volt output. I changed it and the output went to 3.3. I was lucky I didn't burn the HDMI ci. | Before changing the HDMI IC, check its supply voltages. | RDS |
| PHILIPS |
AS 405
|
Power led does not light | Just give it a touch | Fredy | |
| PHILIPS |
43PFL3707D/78
|
Shutting down, it crashed on startup | Regulator u701 g1084-33tu3uf, 3v3 regulator varying voltage between 3v6 and 3v7 | Replace the regulator and add the c719 220μF 16v, go for the hug | Valdecir Schena |
| PHILIPS |
32PFL3606
|
Resistor next to the indication k1 with a value of 750k/smd | You are giving tips without even checking the model, this solution described is for model 32pfl3605 and it does not work for 32pfl3606, pay more attention to what is posted without checking the correct model guys | ||
| PHILIPS |
FW-C505
|
I'm sound | 7501 tda 7468d ruim | To replace | Adriano |
| PHILIPS |
50PUG6513/78
50PUG6513/78 |
Does not turn on, no standby. | Shorted mosfets and blown ceramic capacitor | Power supply board 715g8967-p02-009-001s with the power supply board fuse open (5a-250v) replace but first replace the 02 mosfets q9102 and q9101 (k10a50d) and the 02 ceramic capacitors that sit on top of them 101k 1kv | MARCO BORSATO - MEDTEC INFORMATICA |
| PHILIPS |
47PFL4007G-78
|
Turns on in a few seconds turns off to turn on again you have to wait a while | Altered or faulty 3.3v regulator u701 g1084 -33 |