Search: Cce
Results: 4810
Results: 4810
Cce Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
C420
|
Flashing screen | Remove the plate from con1 and place a 27k collector resistor z2 to rj5 (0Ω resistor) | HP ELETRONICA | |
| CCE |
STILE D42
|
It is completely inoperative, voltage of 5v with 5.1 and standby 2.8v. So I was suspicious of the 1.8 regulator, as it showed 1v at the output. | Ruins components: ec4 capacitor, 1.8v u5 regulator. | Solved just by replacing capacitor ec4, regulator 1.8v u5. | |
| CCE |
STILE D4201
|
Red LED is weak and does not change to green. | Change 470uf x 16v ec2 and ec4 capacitors, both on the main board. | Persio (TVCompany) | |
| CCE |
LCD STILE D42
|
Turning off backlight | Make a palliative (at your own risk) | Remove the con1 plate and place an 82k resistor between rj5 and z2 (on the side that only has one terminal) | Eletrônica Cecé, Brumadinho MG |
| CCE |
LH42G
|
TV doesn't turn on | Mains fuse blows after a few minutes and q2 shorts out (fqnf13n50c) | 82μF/450v capacitor open at power supply | Eletrônica Marinho |
| CCE |
TV2118USP
UOC-TOP TV2118USP |
Alloy with rgb lines then retrace at the top and black line at the top | Defeito vertical capacitor c 302 10uf/35v | C302 replacement | Ricardo |
| CCE |
D32 STILE
|
When turned on, the speakers make a noise and go off, repeating 3 times and the green LED continues with no image | In my case it was cold soldering, resoldering the power supply board and running for hugs | Eletrônica Moura trindade | |
| CCE |
HPS 1473
CHASSIS 34BI |
Vertical closing | Fr0403 burned or open | Just replace and run for the hug, I'm grateful for the help I've already had | Rogério TV |
| CCE |
STILE D3201
|
Lamps come on and then go off and the LED on the power supply blinks | Always test whether the pins of capacitors c33 and c29 are leaking, as this will cause the lamps to go out. | ALBERI F S | |
| CCE |
STILE D3201
|
Lamps come on and then go off and the LED on the power supply blinks | Leak in transistor d20 connected to the cap. c33, remove and clean the area and resolder it, in my case it did the trick. | ALBERI F S | |
| CCE |
D32
|
It doesn't turn on, the red LED lights up very weakly and it doesn't accept power, it doesn't come out of it. | Regulator on the 1.8v main board next to the u3, I forgot to check the position, because I had already closed the TV. | Sequence of turning on this TV: connect to power, LED lights up faintly in red, then turns very bright red and while it is in red It is almost imperceptible, but gives a quick blink, This is when the cycle of loading the eprom data lines has completed , then the TV is able to press the power button and it turns on and the LED turns green... ok | MIGUELTV |
| CCE |
HPS-2198AV
|
Totally off | Short in the tsh area but it wasn't tsh but d807 | Replace d807 burned or shorted | Rogério TV |
| CCE |
C24
|
Does not turn on, stand by LED is orange instead of lighting red and then green when turned on. | Diode d11 in4007 change without testing and go for a hug. | ALBERI F S | |
| CCE |
TV - 2118 USP / AV
|
White and colored lines at the top of the screen | C 412 of 100uf / 63v | Replace | Mauro Mascarenha Tel. (88) 981422821 |
| CCE |
TV - 2118 USP / AV
|
When you increase the volume the sound becomes shaking and the image shakes | Capacitor da power supply c 831 de 1000uf /25v | Replace | Mauro Mascarenha Tel. (88) 981422821 |
| CCE |
TL660
|
TV with stand by LED on but it wouldn't turn on | After changing the 1000mf capacitors on the power supply, the TV turned on but the screen lamps kept blinking. Solution: Change the 100mf 25 volt capacitor c28, after changing the TV, it returned to normal | Eletromad | |
| CCE |
HPS-21AVP (HPS-2118)
H-2197A |
Does not turn on c805 stays charged | Bad pwm observes the fr804 if it is open | Replace ci pwm under the board and fr 804 | Rogério TV |
| CCE |
LN39G
|
Stays on standby and doesn't turn on | Button board | After testing all the boards and replacing the 2, the TV still didn't turn on, I saw that tsound was a broken wire in the controls and someone had already soldered it and it didn't solve it, this is the second time that this board had a defect, this display works on LG Smart 39 So as it was my own TV I decided to mount the screen on the LG | william joner |
| CCE |
STILE D32
MIP123 |
Doesn't start | Fat resistor ci smd | Changing the main power supply fat, plus 4 smd resistors in parallel, they are 3 1r resistors and a 2r2 plus a 470r smd resistor and the 6pin smd ci, i had to remove it from another board, you can't even see the code from him. | Jas plaza |
| CCE |
STILE D3201
|
Turns on and off with sound and image. d21 led flashing | Resolder the terminals of the con1 board next to the d21 led | Medeiros Eletrônica - MG |