Search:
Results: 87305
Results: 87305
Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG |
PL42A450P1XZD
|
Hitting relay | Capacitor cs823 47/100v 105º power supply bn44-00206a | Replace without measuring | SANTOMEL |
| PHILIPS |
FWM998/78
POW600 |
Sound turns on demo mode partially but does not start | +12v low voltage, it was measuring below 9v. In the region of the inductors l1 and l2 of the power supply, the solders were oxidized and tsound was that disgusting glue that after a while gives conductivity. | Redo the welds in the region and remove all this factory glue. Don't forget to sand the legs of the inductors and capacitors. | Tiago C. Neves |
| PHILIPS |
46PFL7606
|
Does not turn on, LED flashes 3x | Check q403 and q402 LED power supply circuit, one of them has a short circuit. | Mirage Eletrônica | |
| SAMSUNG |
UN50RU7100
|
Restarting (screen symptom) | Check c99 to c104 vcon | Junior - Tecnoprom | |
| SAMSUNG |
UN32FH5203G
|
Does not turn on, standby on | Short in the 5v line on the main board | Ic201 shorted on the main board, replace it. | NiloTech |
| PHILIPS |
FW-C380
FW-C380 |
Digital erased 4r7 open | Digital erased 4r7 open-3211 on board | "3211" resistor 4r7 on the power supply board | NEUPSX4 |
| PANASONIC |
TC-L42E30B
|
League. dark image on one side. turns it off and goes back to stb. | Changing LEDs. reverse repair. | Resolder or replace the 2 series of 3 resistors. (one series for each bar) | EDU PINHO |
| PHILCO |
PH21C
|
Darkening the screen. in a few minutes it becomes very dark. | Q513, q523, q533 (all bf423) on the kinescope board. It's usually the bf422 that cause the most problems, but that wasn't my case. | R-Tec | |
| PHILIPS |
55PFG5100
0000 |
Retrace or bands on the screen | Short display | Technical arrangements or workaround lol... on cn 3 I isolated 3 ways 40 to 43, it was clean and crystal clear qsl macanudo lol.... | Jhone Eletronica |
| SEMP |
U17
|
Dark image and sound | Cold solder on pin 15 and 16 of the do-all next to the c430. no vertical voltage and the flat back screen does not work and the 180v only has 70v equal to +b | Fábio boysinnn | |
| LG |
42LG6000
|
Loose scratches in the image | The problem is in the two 100uf smd capacitors on the board between the t-con and the mainboard (c403 and c398). the capacitors are both in the lower right corner of the board. just replace these capacitors and the problem will be solved. | Shakti | |
| SAMSUNG |
LB40B530
|
Turns on normally after turning off the backlight | Weak lamps, with darkened cathode | ALDEIATEC | |
| CCE |
C420
|
Flashing screen | Remove the plate from con1 and place a 27k collector resistor z2 to rj5 (0Ω resistor) | HP ELETRONICA | |
| SEMP TOSHIBA |
DL3971
|
LED does not turn on, flashing red and green quickly | Diode in power supply | Direct replace dp9 diode ba158 | JORGE TV TÉCNICA PARANÁ |
| PANASONIC |
TC-L32U30B
|
Works for a while and turns off, stand by blinks once, lamps blinking. | Pfc low, this TV works with 380v | Faulty protection circuit, remove diode d7209 below IC7201, if the voltage rises, replace Q702 without measuring. | Eletrônica JJ |
| PHILIPS |
32PFL3404
|
It turns on the sound, the video is loud, and the screen is bright, but then it turns off. | Support for two LCD lamps loose. | I resolved the two and reinforced the others. | Ademir tc |
| SAMSUNG |
PL43F4000
|
Turns on has sound and video, but turns off. | Welds with poor contact and especially in cs809s, redo the welds at the power supply. | Ademir tc | |
| CONTROLE PS4 |
CONTROLE PS4 JDM-055
JDM-055 |
Ps4 jdm-055 control diagram | Jdm-055 | <a href="https://electronica-pt.com/su/16" rel="nofollow" target="_blank">external link... </a> | NEUPSX4 |
| SAMSUNG |
QN50Q60
|
Blue screen, restarting | The defect was in the v-com on the right side, I isolated some tracks of the flat that made the connection between the plates and the image returned to normal | ||
| BRASTEMP |
BMT45
|
Operating the keyboard alone | Remove the acrylic from the panel with a wrench on the sides, wash the board and then resolder all the components one by one until the circuit is integrated | reginaldo moronte, eletronica junior caldas novas |